Plant pots and accessories

Accessories for the Palatino series offer another way to use the planters in a variety of ways. With the retrofit kit, consisting of a multi-part insert, planters can be created at a height of 25 cm. Simply insert the insert into Carlotta, eliminating the need for angled pieces – now you can plant at a height of 25 cm. This allows for tiered arrangements, and if you place the base in the extension frame, you only need 25 cm of soil. This makes changing plants seasonally easier. If you want to plant at a height of 75 cm, use Clara or Lotte and place Carlotta with the base on top or underneath. This way, you can fill it with less soil and only need to weigh it down at the bottom to prevent it from being top-heavy. There are many design options: The bases are always the same for all tubs/planting frames, always made of galvanized sheet steel. Technical data • Two- or three-part base plates for insertion • Screw set with flange head screws and nuts • Screwed-together base plate for insertion • Perforated base for drainage • 1 mm galvanized steel sheet guarantees high load-bearing capacity Production takes place on modern CNC machines with optimal dimensional accuracy. We are committed to our German production site and handle all manufacturing in-house. That's our quality promise!

Read more less

Accessories for the Palatino series offer another way to use the planters in a variety of ways. With the retrofit kit consisting of four brackets and the necessary screws, all plant pots can be used easily and stably as plant frames without a base. Production in the respective material of the vessels Technical data • Corner bracket: 6.7x6.7x0.1 cm; Sheet thickness 1 mm • 4 reinforcing angle brackets for the corners, for screwing in • Screw set with flange head screws and nuts M5 • The necessary holes are already present in the lower edge • No screws visible from the outside, easy installation, no floor required • Available in three material variants (zinc, Corten, anthracite) - Corten steel mill finish! Production takes place on modern CNC machines with optimal dimensional accuracy. No comparison to cheap imports from the Far East. We are committed to our German production site and handle all manufacturing in-house. That's our quality promise!

Read more less

Accessories for the PALATINO series (Lotte, Nora, Clara, Carlotta and table planters) contains - 20 pcs. M5x8 electro-galvanised lens flange head screws - 20 pcs. M5 bare electro-galvanized nuts, hexagonal, with flange

Read more less

Accessory for the PALATINO series, for insertion into the lower edge perforation. With the retrofit kit consisting of four 20 mm diameter buffers, you can provide a soft base for the buckets and make them more difficult to move. Since there are two holes at each corner, we recommend inserting two buffers there; therefore, it's best to order two sets (8 buffers). Rubber disc height 4 mm, bridge length 12 mm - simply insert, it holds! Can also be used for drilling holes in the Woodpecker PRO! Technical data • Insert buffer: Ø 20 mm, height 4 mm, web length 12 mm • Suitable for 5mm screw holes (Ø 5.5 mm)

Read more less

The connection system creates the possibility for the perfect connection of the elements from the »Palatino« series . If the ground is uneven or a permanent arrangement of several beds directly next to each other is desired, we recommend additional connection using our "Connect" rail system. This is embedded approximately 6 cm into the ground or laid above ground and covered, for example, with stones so that it is no longer visible. Also available upon request: Length 200 cm (shipping via freight carrier!) A NOTICE: Always make sure that the lengths of the rails are chosen so that the connection points are as close as possible to the middle of the elements! Modular design, lateral arrangement in a row or at a corner, anything is possible - particularly useful in urban gardening, for example to systematically arrange several raised beds - for corner arrangements you will also need corner connectors / end profiles the depth of the element, For example, with a 100 cm wide x 40 cm deep planter, you would need a 40 cm corner piece; in principle, you could also add a 60 cm deep element, in which case you would also need to order a 60 cm long corner piece, and so on. Production takes place on modern CNC machines with optimal dimensional accuracy. No comparison to cheap imports from the Far East. We are committed to our German production site and handle all manufacturing in-house. That's our quality promise! Technical data • Profile dimensions WxH: 40x60 mm, length variable, connector for insertion slightly smaller • Holes for screwing together the raised beds / planters • Available in various lengths, max. length 1.2 m, further extensions are achieved using a connector. • incl. screws and nuts • Choose the length of the individual rail sections so that they are at least 10 cm shorter than the buckets, This means there is no connection point directly at the transition between raised beds! • The individual elements of the raised bed or tub can also be perfectly arranged in a row or at an angle. • Weight approx. 1 kg per linear meter

Read more less